en

Cleaners for interiors and exteriors of TM Ardrox

Paint strippers for polyurethane aviation paints and epoxy primers (aviation removers)

Product name

Application methods

Concentration

Temperature

1.

Ardrox 2526

Application type paint remover, designed to remove the more resistant types of polyurethane and epoxy surface coatings. The product contains chlorinated solvents and phenolic materials. It also readily removes air-cured polyurethane and epoxy paint schemes from aircraft skins, road transport vehicles and other painted surfaces. It is readily rinsed off with water, leaving a clean surface.

Brush/Spray or using Ardrox setup for cleaning under pressure

As supplied

Ambient

2.
Ardrox 2871

Application type paint remover, designed to remove the more resistant types of polyurethane and epoxy surface coatings. The product contains chlorinated solvents and phenolic materials. It also readily removes air-cured polyurethane and epoxy paint schemes from aircraft skins, road transport vehicles and other painted surfaces. It is readily rinsed off with water, leaving a clean surface.

Spray

1,02-1,05 g/cm³

100 °C
3.
Ardrox 204

Water rinseable general-purpose application paint remover for a wide range of paint finishes including chromate primers.

Brush/Spray

As supplied

Ambient

4.
Ardrox 2106

Low viscosity product for spray applications (also available is a high viscosity product ARDROX 2106HV for brush-on application). These versatile products will remove a wide range of paint schemes including alkyds, acrylics, celluloses, zinc chromate primers and especially polyurethane on etch (wash) primer.

Brush/Spray

As supplied

Ambient

5.
Ardrox 2302

A non-methylene chloride mixture of solvents, activators and corrosion inhibitors comprising two layers, the upper layer being an oil seal to minimize the evaporation of solvents in the lower, active paint removing layer. It removes a wide range of paint schemes; including stoved acrylics, epoxies, polyurethanes and phenolics. It will also remove carbon or carbonaceous deposits, polymerized gum and lacquer deposits.

Immersion

As supplied

80-100 °C
6.

Ardrox 2320 (A & B)

A di-phase aqueous blend of solvents, activators and corrosion inhibitor for removing a variety of organic finishes.

Immersion/Spray

10% A &

5% B (v/v) in demin. H20

Ambient to 55 °C

7.
Ardrox 2480

An acid-activated paint remover containing a wax seal to retard evaporation losses. It is intended for the removal of paints and organic coatings that are resistant to the more usual cold immersion processes. It is useful for the removal of stoved acrylics, epoxies, nylon and multi- coat systems, which occur on painting jigs.

Immersion

As supplied

Ambient

8.
Ardrox 266

A blend of solvents, surfactants, activators and corrosion inhibitors. It separates in two layers, the upper aqueous layer minimizes evaporation of volatile constituents in the lower layer. Particularly effective in the removal of stoved epoxy and polyurethane paint films. It also efficiently removes many other industrial paint finishes.

Immersion

As supplied

Ambient

9.
Ardrox 2814

Thickened, non-methylene chloride, acid-based paint stripper. Not for use on magnesium.

Brush/Spray

As supplied

Ambient

10.
Ardrox 2870

Thickened, non-methylene chloride neutral paint stripper for vertical surfaces. Its combination of neutral pH and low odour makes it an excellent choice in areas where personnel are working.

Brush/Spray

As supplied

Ambient

11.
Ardrox 29

A di-phase product consisting of a highly active acidic lower layer and an upper layer that forms an insoluble seal. It is used to remove difficult paint schemes and coatings, which are normally resistant to chlorinated paint removers. It finds particular application in the removal of Kearsley lacquer and stoved silicone epoxy based coatings.

Brush/Spray

As supplied

Ambient

12.
Ardrox 3000W

A thickened, non-flammable paint stripper that effectively removes epoxy, polyurethane and similar organic coatings from metal surfaces. Contains methylene chloride and phenol.

Brush/Spray

As supplied

Ambient

13.
Ardrox 666/6

A blend of solvents, surfactants and corrosion inhibitors with an aqueous seal to minimize solvent losses by evaporation. It will quickly and easily remove hard carbon, sticky gums, varnish and baked on paint and is of particular value to the automotive, marine, aircraft and electricity generating industries, in the maintenance and overhaul of diesel and petrol engines and other on-site plant and equipment.

Погружение

As supplied

Ambient

General purpose exterior cleaners

Product name

Application methods

Concentration (% v/v)

Time (mins.)

pH
1.
Ardrox® 1900 B

A heavy duty, thixotropic, alkaline cleaner for the exterior and interior cleaning of aircraft and ground handling equipment. It can also be used as a decarbonizer for engine and component cleaning. It is pleasantly scented and all the surfactants employed in the formulation are completely biodegradable.

Spray/Brush/

Mop

5-10 Interiors

20-50 Exteriors

5-10
11.0
2.
Ardrox® 1900 BL

Low foam version of Ardrox 1900B designed to cling to vertical surfaces.

Spray/Brush/

Mop

10-20
1-5
12.0
3.
Ardrox® 6021

A thickened blend of alkalis, water soluble solvents and surface-active agents; free from phosphates and petroleum solvents. Pleasant smell and easy rinsing leaving a streak and spot free surface.

Spray/Brush/

Mop

10-20
5-10
9.0-10.0
4.
Ardrox® 6086

Cleaning of the exterior surfaces of aircraft using a foam applicator and by spray or brush application. It may also be used for cleaning ground equipment.

Spray/Brush/

Mop

 
10-20
5-10
12.7
5.
Ardrox® 6472

Exterior cleaning for general purposes and heavily soiled areas such as smoke stained areas, engine nacelles, underwing flaps, landing gear and wheels/wheel bays.

Spray/Brush/

Mop

2-25
5-10
11.5

Heavy duty exterior cleaners

Product name

Application methods

Concentration (% v/v)

Time (mins.)

pH
1.
Ardrox®245L

Heavy duty, stable emulsion cleaner, consisting of a blend of biodegradable surfactants, organic solvents, corrosion inhibitors and water. It is used for the cleaning of aircraft exterior and ground handling equipment.

Spray/Brush/

Mop

Full strength

5-10
10.8-11.4
2.
Ardrox®1900B

A heavy duty, thixotropic, alkaline cleaner for the exterior and interior cleaning of aircraft and ground handling equipment. It can also be used as a decarbonizer for engine and component cleaning. Pleasantly scented and all the surfactants employed in the formulation are completely biodegradable.

Spray/Brush/

Mop

Full strength

5-10
11.0-12.0
3.
Ardrox® 6021

A thickened blend of alkalis, water soluble solvents and surface-active agents; free from phosphates and petroleum solvents. Pleasant smell and easy rinsing leaving a streak and spot free surface.

Spray/Brush/

Mop

Full strength

5-10
9.0-10.0
4.
Ardrox® 6085

Heavy-duty, exterior cleaning for heavily soiled areas such as smoke stained areas, engine nacelles, underwing flaps, landing gear and wheels/wheel bays.

Spray/Brush/

Mop

Full strength

5-10
12.7
5.
Ardrox® 6472М

Heavy-duty exterior cleaning for general purposes and heavily soiled areas such as smoke stained areas, engine nacelles, underwing flaps, landing gear and wheels/wheel bays. Thick- ened version of Ardrox 6472.

Spray/Brush/

Mop

Full strength

5-10
9.8
6.
Ardrox®1820

Highly effective concentrated liquid detergent sanitizer and deodorant used at dilutions of up to 60 parts with water. ARDROX 1820 contains a powerful detergent system that rapidly emulsifies grease.

Spray/Brush/Mop

> 1.5
5-10
11.9
7.
Ardrox®1900B

A heavy duty, thixotropic, alkaline cleaner for the exterior and interior cleaning of aircraft and ground handling equipment. It can also be used as a decarbonizer for engine and component cleaning. Pleasantly scented and all the surfactants employed in the formulation are completely biodegradable.

Spray/Brush/Mop

Full strength

5-10
11.0-12.0
8.
Ardrox® 6012

Foam cleaning of painted and unpainted metal surfaces and of vinyl fabrics. Supplied as aerosol.

Aerosol/Wipe

Ready to use

5-10
10.2-10.6
9.
Ardrox® 6076

Based on a blend of natural citrus solvents, emulsifiers and surfactants; this is petroleum solvent free. Ardrox 6076 will remove a wide range of soils including oils, greases, chewing gum, tar, inks, adhesives, tyre marks, decals and soap scum.

Spray/Brush/Mop

Full strength

5-10
4.0-6.0
10.
Ardrox® 6427

Removal of dirt and soil contamination from surfaces such as glass, metal and plastic. It will remove a wide range of soils including oil, grease, fingerprints, tea and coffee stains and other soils from aircraft furnishings. In areas with very high soil contamination, it may be necessary to rinse the surface with water after application of the cleaner.

Spray/Brush/Mop

4-15
5-10
12.4-12.8

Carpet & upholstery cleaners

Product name

Application methods

Concentration (% v/v)

Time (mins.)

pH
1.
Ardrox®485R

Gentle removal of deeply embedded dirt from wool and synthetic fiber carpets using a Hydro-Soil Extractor type cleaning machine. Also freshens carpets and gives revived lift and life. Contains soil retardants, optical brighteners, odour eliminators, anti-static agents and is non-corrosive.

 

Machine

1-2
12.4-12.8
2.
Ardrox® 6082

Carpet and upholstery cleaner for machine use or with a brush for spot cleaning by hand.

Machine/Brush

2.5
9.0

Transparency cleaners

Product name

Application methods

Temperature,

(°C)

Concentration (% v/v)

Time (mins.)

pH
1.
Ardrox® 6077

Mildly alkaline product formulated specifically to safely clean aircraft windows. Blend of surfactants and isopropanol. Wax- free and non-corrosive.

Spray

Ambient

30-100
2

In-process and primary cleaning

Product name

Application methods

Temperature,

(°C)

Concentration (% v/v)

Time (mins.)

pH
1.
Ardrox® 1064K

Removal of oils, greases, adhesives and some paints from metal surfaces.

Wipe/Immersion

Ambient

Full Strength

2.
Ardrox®1900B

Heavy duty, thixotropic, alkaline cleaner for aircraft exterior and interior cleaning and ground handling equipment. It can also be used as a decarbonizer for engine and component cleaning. It is pleasantly scented and all the surfactants employed in the formulation are completely biodegradable.

Spray/Brush/

Mop

Ambient to 65

10-50
10-30
11.0
3.
Ardrox® 5501

A solvent mixture for the degreasing of metal surfaces and solvent resistant coatings. It is free of halogens and aromatics. Flashpoint: <0°C.

Brush/Mop

Ambient

Ready to Use

4.
Ardrox® 5502

General solvent cleaner for oils and grease leaving the surface in a dry condition. Flashpoint: 41°C.

Spray/Brush/

Mop

Ambient

Ready to Use

5.
Ardrox® 5503
 

General solvent cleaner for oils and grease leaving the surface in a dry condition. Flashpoint: 63°C.

 

Spray/Brush/

Mop

Ambient

Ready to Use

6.
Ardrox® 6085

Heavy duty, exterior cleaning for heavily soiled areas such as smoke stained areas, engine nacelles, underwing flaps, landing gear and wheels/wheel bays. Also a very suitable and effective wipe on/wipe off cleaner and even finds application in the workshops as a convenient alternative to soak tank cleaning processes for dirty parts and carbon removal.

Spray/Brush/

Mop

Ambient to 65

10-50
10-30
12,7
7.
Ardrox® 6333

Removal of oil, grease and soft carbon deposits in spray washing machine applications. Low foaming at elevated operating temperatures. Other uses include engine and component cleaning by immersion and general hard surface cleaning.

Machine/

Immersion

60-70 °C
5-10
5-10
12
8
Ardrox® 6475

A concentrated liquid aqueous alkali cleaner. Used by immersion for the removal of oil, grease and soft carbon deposits. Contains biodegradable surfactants.

Immersion

55-65 °C
15-25
15-30
12
9
Ardrox® 6333А

Removal of oil, grease and soft carbon deposits in spray washing machine applications. Low foaming at elevated operating temperatures. Other uses include engine and component cleaning by immersion and general hard surface cleaning.

Machine/

Immersion

40-70 °C
2-10
15
9.0
10
Ardrox® 6376

Silicated, mildly alkaline, low-foaming, multi-metal safe cleaner.

Immersion

40-70 °C
20

As specified

8.0 – 9.0
11
Ardrox® 6471

A heavy-duty, liquid cleaner formulated to remove difficult soils in agitated parts cleaning tanks. It will remove heavy oils, grease, cosmoline, and other production soils. Because it is inhibited, it can be used to clean aluminium alloys.

Immersion

40-70 °C
8-12
15-30
12.5-13.3

Gas path cleaners

Product name

Temperature,

(°C)

Concentration

pH

Form

1.
Ardrox® 6367

In-situ washing of the compressor stages of gas turbine engines for removal of accumulated of atmospheric impurities, oil and oil oxidation products that occur in these areas. It is suited for both hot-fired and off-line washes. Application method: spray.

Ambient

20 % (v/v)
7.7

Liquid

2.
Ardrox®6375

A blend of detergents and emulsifiers, for removing atmospheric soils, oils, carbon and salt deposits during “in- situ” hot-fired and cold motor washes. It safe on all aircraft metals, plastics, windows, etc. Application method: spray.

Ambient

20 % (v/v)
9.0-9.5

Liquid

3.
Ardrox® 6377

A liquid alkaline product formulated to clean the compressor sections of gas turbine engines. A blend of detergents and emulsifiers, it removes atmospheric soils, oils, carbon, and salt deposits during “in-situ” hot-fired and cold motor washes. Safe on all turbine metals, non-flammable and biodegradable. Regular use helps maintain peak engine efficiency and reduces maintenance and fuel costs. It is compatible with recognized antifreeze materials used for cold weather cleaning and should be diluted with demineralized water. If demineralized water is not available, then use the ready to use formula Ardrox 6377 RFU. Application method: spray.

Ambient

20 % (v/v)
7.5 – 8.5

Liquid

Rust, scale and carbon remover

Product name

Temperature,

(°C)

Concentration

pH

Form

1.
Ardrox® 1218

Rust and oxide layers remover, appeared as a result of heat treatment and welding of ferrous materials. It is used for removing corrosion from aluminum, copper and zinc materials. Particularly suitable for the processing of chrome-plated iron and parts with very close tolerances.

Ambient to 60

10-50 % (v/v)

1 at 20 °C

Colorless liquid

2.
Ardrox®188

A powder product containing an oxidizer. Used as auxiliary substance for the removal of particularly strong scale with a high alloy steel, nickel and cobalt alloys. The main area of application – during the partitions of the distributors of jet engines. Suitable for removing strongly adhered residue, resulting in the hardening.

95-100

160 g/l

14 at 160 g/l

(at 20 °C)

White, darkviolet powder

3.
Ardrox® 185

Strongly alkaline, sequestrant containing water-soluble powder, containing the substance to enhance excretion. Ardrox® 185 is also available as a 50% aqueous solution with product name Ardrox® 185L. Ardrox® 185 on dilution is excellent in removing oil, grease and some air-dried paints.

80-88

10-30% (100-300 g/l)

14 at 100 g/l

Whitish powder

4.
Ardrox® 1900С

A heavy duty, thixotropic, alkaline cleaner for the exterior and interior cleaning of aircraft and ground handling equipment. It can also be used as a decarbonizer for engine and component cleaning.

If necessary, it can be heated to 65

The original concentration 10-50% or depending on the type of contamination

12,5

Viscous white or pale yellow liquid

 
5.
Ardrox® 6376
 

Highly active and biodegradable cleaning concentrate for immersion. Removes grease, oils, soot and carbon deposits on steel, iron, aluminum, magnesium, copper and other alloys.

 
60-80

20%

8.0-9.0

Yellowish, transparent liquid

6.
Ardrox® 1618
 

A caustic alkali concentrated mixture of sequestrants and surfactants. Particularly effective in cleaning ferrous internal combustion engine components that are heavily contaminated in service, e.g. valves, cylinder heads. It removes carbon, paint, rust and lead deposits and is also used to decarbonize other items such as rubber moulds.

 
80-90
25 % (v/v)

Liquid

Non-destructive testing

Product name

Application methods

Density

Form

1.
Ardrox® 9D1B

ARDROX 9D1B, nonaqueous developer with organic solvent. It is a suspension of an inert white powder in a quick drying solvent. It has a low sulphur, halogen and alkali metal content.

ARDROX 9D1B, nonaqueous developer with organic solvent. It is a suspension of an inert white powder in a quick drying solvent. It has a low sulphur, halogen and alkali metal content.

0,88 g/ml at 20 °C

White powder

2.
Ardrox® 9D4A

Dry powder developer is a homogeneous blend of synthetic white powders of fine particle size. Application of this developer renders any defect indications much easier to see when viewed under ultra-violet light (black light) than conventional powder developers. The time of contact with the developer should be minimum 10, maximum 30 minutes before inspection under UV rays.

Spray

110 g/l

Soft, granular, white powder

3.
Ardrox® 9702-9705

Water washable fluorescent penetrants. They give clear indications with exceptionally low background level. Great for electrostatic applications. Can be used for metals and ceramics which are not strongly porous. They have different sensitivity levels. Flashpoint 93 (°C).

Brush/Immersion/Electrostatic spraying

from 0,86 g/sm³ to 0,88 g/sm³

Transparent liquid with a yellowish-greenish tint

Carbon cleaners

Product name

Application methods

Temperature,

(°C)

Concentration, (% v/v)

Time (mins.)

pH
Ardrox® 1618

Cleaning of ferrous engine components, that are heavily contaminated in service. It removes carbon, paint, rust and lead deposits.

Immersion

80-90
25
15-30
>14
Ardrox®1900B

A heavy duty, thixotropic, alkaline cleaner for the exterior and interior cleaning of aircraft and ground handling equipment. It can also be used as a decarbonizer for engine and component cleaning. Pleasantly scented and all the surfactants employed in the formulation are completely biodegradable.

Immersion/SprayBrush/

Mop

Ambient to 65

10-50
10-30
11.0
Ardrox® 2320 (A&B)

A diphase aqueous blend of solvents, activators and corrosion inhibitors for removing a variety of organic finishes.

Immersion/Spray

To 55

10 A &

5 B in demin. H20

240 max

12.0-12.5
Ardrox® 2302

It removes a wide range of paint schemes; including stoved acrylics, epoxies, polyurethanes and phenolics. It will also remove carbon or carbonaceous deposits, polymerized gum and lacquer deposits.

Immersion

80-100

Ready to Use

240 max

N/A
Ardrox® 2410B

Removal of carbonaceous deposits from aircraft exteriors and thrust reversers. Thixotropic, water washable. No petroleum distillates or chlorinated solvents.

Spray/ Brush/ Mop

Ambient

Ready to Use

15-60
15-60
Ardrox® 66Х series

For the removal of hard carbon and paint from engineering components and equipment. A good general purpose, immersion paint remover and will usually remove most types of organic finish. It is supplied and operated as a diphase system.

Immersion

Ambient

10-50
10-30
11.0

Paint and rust removers

Product name

Application methods

Temperature,

(°C)

Concentration, (% v/v)

Solvent

Form

Ardrox® 185

Strongly alkaline, sequestrant containing water-soluble powder. On dilution it is excellent in removing rust from iron and steel, as well as removing oil, grease and some air-dried paints. Does not cause hydrogen embrittlement of ferrous based alloys and reduces the tendency for rerusting compared to conventional acid pickling techniques.

 

Immersion

80-85
10-30
n.a.

Powder

Ardrox®185 L

A water miscible strongly alkaline solution containing sequestrants. Primarily intended for the removal of rust from iron and steel but also capable of removing oil, grease and some air-dried paints. Will not cause hydrogen embrittlement of high tensile steels and reduces the tendency for rerusting compared to conventional acid pickling techniques.

Immersion

80-85
25-50
n.a.

Liquid

Ardrox® 1618

A caustic alkali concentrated mixture of sequestrants and surfactants. Particularly effective in cleaning ferrous internal combustion engine components that are heavily contaminated in service, e.g. valves, cylinder heads. It removes carbon, paint, rust and lead deposits and is also used to decarbonise other items such as rubber moulds.

Immersion

80-90
25%
n.a.

Liquid

Exhaust and thrust reverser cleaners

Product name

Application methods

Temperature,

(°C)

Concentration, (% v/v)

Time (mins.)

pH
Ardrox® 2410B

Removal of carbonaceous deposits from aircraft exteriors and thrust reversers. Thixotropic, water washable. No petroleum distillates or chlorinated solvents.

Spray/ Brush/Mop

Ambient

Ready to use

15-60
12.0-13.0

Solvent cleaners

 

Product name

Application methods

Temperature,

(°C)

Concentration, (% v/v)

Density

Flashpoint (°C)

1.
Ardrox® 5502

General solvent cleaner for oils and grease leaving the surface in a dry condition. Flashpoint: 41°C.

Spray/Brush

Ambient

Ready to use

0.78
41
2.
Ardrox® 5503
 

General solvent cleaner for oils and grease leaving the surface in a dry condition. Flashpoint: 63°C.

 

Spray/Brush

Ambient

Ready to use

0.79
63
3.
Ardrox® 5564

Non-chlorinated solvent. Good for cleaning paint spray guns and adhesive application equipment.

Immersion/Wipe

Ambient

Ready to use

0.83
24
4.
Ardrox® PR1

Clear, water soluble, non-chlorinated, mobile solvent. It is a solvent penetrant remover used for the removal of visible red dye penetrants and fluorescent penetrants in aerosols. It can also be used as a solvent precleaner prior to the penetrant application or as a general solvent cleaner to remove oils, grease and dirt..

Spray/Brush/Mop

Ambient

Ready to use

0.78
12

Wax remover

Product name

Application methods

Concentration, (% v/v)

Time (mins.)

Flashpoint

Form

Ardrox® 5414

A blend of solvents and emulsifiers formulated for the removal of “stop-off” wax from plated metal components. It has a high flash point, is used hot and rinses off completely with tap water.

Immersion

 

Ready to use

3-10
165 °C

Liquid

Pre-impregnated wipes

Product name

Application methods

Temperature,

(°C)

Concentration, (% v/v)

Density

Flashpoint

Form

Ardrox® 5531

Impregnated low lint, high strength wipes enabling the application of the optimum amount of product, to prevent wastage of the AX 5531 and minimize VOC levels. This combination is used for the removal of various contaminants such as uncured polysulphide sealant, grease and oils.

Wipe

Ambient

Ready to use

1.03
61

Wipe

Cleaning napkins

Product name

Application methods

Temperature,

(°C)

Concentration, (% v/v)

Density

Flashpoint

Ardrox® 3961

Blend of surfactants, corrosion inhibitors and oil in a petroleum-based solvent. Excellent dewatering and penetrating properties. Leaving a thin, oil film on articles, it imparts good indoor corrosion protection. Not recommended for outdoor storage where, e.g. Ardrox 3302 or 3140 should be used.

Wipe

Ambient

Ready to use

0.84
>38

Wipe cleaners

Product name

Application methods

Temperature,

(°C)

Concentration, (% v/v)

Density

Flashpoint (°C)

Ardrox® 1064К

Removal of oils, greases, adhesives and some paints from metal surfaces. It may be used by wipe or immersion and rinsed off with water or wiped dry.

Wipe/

Immersion

Ambient

Ready to use

0.84
>38
Ardrox® 161К

Removal of oil and grease from metal surfaces by wipe application.

Wipe

Ambient

Ready to use

0,81
4
Ardrox® 5412

Removal of oils, grease, adhesives, inks, paints and other solvent soluble soils from metal surfaces. It can be used as a wipe solvent or in immersion tanks. Cleaned surfaces may be wiped dry or rinsed with water and dried.

Wipe

Ambient

Ready to use

0,80
48

Runway cleaner

Product name

Application methods

Temperature,

(°C)

Concentration, (% v/v)

Density

Ph
Ardrox® 6331

A low foam cleaner concentrate consisting of an aqueous solution containing surfactants, alkali builders and inhibitors for the removal of grease, oils, dust, sooty deposits and other impinged soils from aircraft stands and runways. Readily produces stable emulsions with oils. It is unaffected by hard water and does not leave any residue or cause any streaking or staining.

Spray/ Brush/Mop

Ambient

10-25
5-10
11.3-12.3

Silicone rubber removers

Product name

Методы нанесения

Temperature,

(°C)

Concentration, (% v/v)

Time (mins.)

Flashpoint (°C)

Ardrox® 2204

Rapid removal of silicone, other bonding rubbers and abradable rubber coatings. Contains chlorinated solvents and is water washable.

Immersion

Ambient

Ready to use

30-300
<1
Ardrox® 2312

Rapid removal of silicone and other bonding rubbers and abradable rubber coatings. The product contains non- chlorinated solvents but is water washable. Immersion application at ambient temperature. Methylene chloride free.

Immersion

Ambient

Ready to use

30-300
N/A

Stand cleaner

Product name

Application methods

Temperature,

(°C)

Concentration, (% v/v)

Time (mins.)

Ph
Ardrox® 6331

A low foam cleaner concentrate consisting of an aqueous solution containing surfactants, alkali builders and inhibitors for the removal of grease, oils, dust, sooty deposits and other impinged soils from aircraft stands and runways. Readily produces stable emulsions with oils. It is unaffected by hard water and does not leave any residue or cause any streaking or staining.

Spray/ Brush/Mop

Ambient

10-25
5-10
11.3-12.3